Radimpex Forum Download HomepageContactTowerArmcadMetal StudioNorma Base

Online Lessons & Tutorials

All lessons and tutorials (movies) presented here at 'Online lessons & tutorials' page are available for download from Download page, allowing you to watch them directly from your computer.

Plane frame

This example shows the model of simple plane frame girder with tie downs (members with non-linear behavior) and contains two films: First film shows the procedure of defining the geometry and cross sections, placing and defining supports and applying loadings. Second film shows results elaboration, including steel stability control.
Download

Film 1 – Data input (4.6MB) Play animation

Download

Film 2 – Results elaboration and steel stability control (2.6 MB) Play animation

Plane truss

This example shows the model of simple plane truss and contains two films. The first film shows the procedure of defining the geometry and cross sections, placing and defining supports and applying loadings. Second film shows results elaboration, including timber stability control.
Download

Film 1 – Data input (4.3MB) Play animation

Download

Film 2 – Results elaboration and timber stability control (2.6 MB) Play animation

Floor structure

This example shows the simple concrete floor structure (slabs and beams) contains 4 films. The first film shows the procedure of defining the geometry and cross sections, placing and defining supports and applying loadings. The second film shows elaboration of results, concrete design and adopting reinforcement in slabs. The third film shows concrete design and adopting reinforcement in slabs. The fourth film shows export of adopted reinforcement into ArmCAD 2005, program for reinforcement detailing.
Download

Film 1 – Data input (2.8 MB) Play animation

Download

Film 2 – Results elaboration and concrete design for slabs (1.7 MB) Play animation

Download

Film 3 - Results elaboration and concrete design for beams (2.2 MB) Play animation

Download

Film 4 – Export of adopted reinforcement to program ArmCAD 2005 (1.8 MB) Play animation

Continual girder

This example shows analysis of one simple model – continual girder, exposed to moving load. The analysis was performed in two ways – using “Moving load” and using “Influence line”. The example consists of two films. The first film shows the procedure for defining geometry and cross section of girder, defining and applying moving load and defining and applying influence line. Second film shows result elaboration, defining loading scheme and obtaining the critical position of moving load.
Download

Film1 – Data input (2.2 MB) Play animation

Download

Film 2 – Results elaboration – moving load and influence line (0.5 MB) Play animation

Workshop hall

This example shows creation and analysis of one simple 3D model – a Workshop hall. The example consists from two films. First film explains the procedure of defining 3D model. Second film shows results elaboration, entity grouping and steel and concrete design.
Download

Film 1 – Data input (5.1 MB) Play animation

Download

Film 2 – Results elaboration - 2D and 3D (4.2 MB) Play animation

Building

This example shows modeling, modal and statical analysis (including seismic analysis) and concrete design of one simple 3D structure - seven-story building. First film shows data input, model generation, f.e. mesh generation and modal analysis. Second film shows results elaboration and concrete design of slabs, beams, columns and seismic walls.
Download

Film 1 – Data input (3.8 MB) Play animation

Download

Film 2 – Results elaboration (2.4 MB) Play animation

Plane frame

This example shows the model of simple plane frame girder with tie downs (members with non-linear behavior) and contains two films: First film shows the procedure of defining the geometry and cross sections, placing and defining supports and applying loadings. Second film shows results elaboration, including steel stability control.
Download

Film 1 – Data input (4.6MB) Play animation

Download

Film 2 – Results elaboration and steel stability control (2.6 MB) Play animation

Plane truss

This example shows the model of simple plane truss and contains two films. The first film shows the procedure of defining the geometry and cross sections, placing and defining supports and applying loadings. Second film shows results elaboration, including timber stability control.
Download

Film 1 – Data input (4.3MB) Play animation

Download

Film 2 – Results elaboration and timber stability control (2.6 MB) Play animation

Floor structure

This example shows the simple concrete floor structure (slabs and beams) contains 4 films. The first film shows the procedure of defining the geometry and cross sections, placing and defining supports and applying loadings. The second film shows elaboration of results, concrete design and adopting reinforcement in slabs. The third film shows concrete design and adopting reinforcement in slabs. The fourth film shows export of adopted reinforcement into ArmCAD 2005, program for reinforcement detailing.
Download

Film 1 – Data input (2.8 MB) Play animation

Download

Film 2 – Results elaboration and concrete design for slabs (1.7 MB) Play animation

Download

Film 3 - Results elaboration and concrete design for beams (2.2 MB) Play animation

Download

Film 4 – Export of adopted reinforcement to program ArmCAD 2005 (1.8 MB) Play animation

Continual girder

This example shows analysis of one simple model – continual girder, exposed to moving load. The analysis was performed in two ways – using “Moving load” and using “Influence line”. The example consists of two films. The first film shows the procedure for defining geometry and cross section of girder, defining and applying moving load and defining and applying influence line. Second film shows result elaboration, defining loading scheme and obtaining the critical position of moving load.
Download

Film1 – Data input (2.2 MB) Play animation

Download

Film 2 – Results elaboration – moving load and influence line (0.5 MB) Play animation

Workshop hall

This example shows creation and analysis of one simple 3D model – a Workshop hall. The example consists from two films. First film explains the procedure of defining 3D model. Second film shows results elaboration, entity grouping and steel and concrete design.
Download

Film 1 – Data input (5.1 MB) Play animation

Download

Film 2 – Results elaboration - 2D and 3D (4.2 MB) Play animation

Building

This example shows modelling, modal and statical analysis (including seismic analysis) and concrete design of one simple 3D structure - seven-storey building. First film shows data input, model generation, f.e. mesh generation and modal analysis. Second film shows results elaboration and concrete design of slabs, beams, columns and seismic walls.
Download

Film 1 – Data input (3.8 MB) Play animation

Download

Film 2 – Results elaboration (2.4 MB) Play animation